变压器油过滤的方法步骤

发布时间：2022-02-22 浏览次数：847次 作者：新澳门3559com机电

       1.罐装油放油时，连接好油管路，高真空滤油机自循环加热油温，滤油机自身清洗，用滤油机清洗热油冲洗油管路，储油罐内部擦洗干净可不用变压器油冲洗，冲洗油要单独存放，做好标志。

       2.桶装油放油时，利用平板式滤油机进行，平板式滤油机使用前，内部要清洗干净，伸进油桶内部油管应使用镀锌管，管口前端加工成45°，两端管口打磨平滑，使用前必须将镀锌管内外擦洗干净，桶装油抽取到底部时，检查油桶底部油质情况，如杂质多，底部油可不抽取。

       3.到达现场的变压器油用滤油机导入到储油罐后，用高真空滤油机进行变压器油过滤，为提高滤油效果，储油罐油过滤应采用倒罐滤油方式，即将一个储油罐内油通过高真空滤油机全部过滤到另一个储油罐内，再从另一个储油罐内过滤到原储油罐内，如果现场储油罐少，采用储油罐自循环，要做好油罐密封，滤油机的出口温度不应低于50℃，过滤后的变压器油要取油样试验，判断变压器油是否净化处理合格，油样可从滤油机取样阀门放油取样。